MenuSearch | Country: United States | Currency: USD
SWiF2-800 80mm 1100 RPM 3-pin Quiet Cooling Fan
Discontinued
More variations available Show

Coolink SWiF2-800 80mm 1100 RPM 3-pin Quiet Cooling Fan

Based on the award-winning original SWiF design, the new SWiF2 series of high-performance quiet fans takes its successful predecessor’s proven qualities one step further by adding hydro-dynamic bearing as well as an unique, exciting colour scheme.

Features

  1. High-performance hydro-dynamic bearing
  2. Protective cable sleeving
  3. Includes Anti-Vibration bolts and metal screws
  4. 9.5 dBA / 19.1 CFM / 1100 RPM

The new hydro-dynamic bearing ensures whisper quiet operation and even better longevity, which is backed up with a massive 60 months warranty. No matter where in your system you plan to install these fans, you can be sure the SWiF2 series provide an exceptional noise to performance ratio that you would expect from Coolink.

SpecificationsSWiF2-800
Size80x80x25 mm
Rotation Speed1100 RPM ±10%
Airflow19.1 CFM
Acoustical Noise9.5 dBA
Input Power0.54 W
Input Current0.05 A
Voltage Range7-13 V
AccessoriesAnti-vibration screws and metal screws
Warranty60 months
EAN barcode4716123313328
SpecificationsSWiF2-800
Size80x80x25 mm
Rotation Speed1100 RPM ±10%
Airflow19.1 CFM
Acoustical Noise9.5 dBA
Input Power0.54 W
Input Current0.05 A
Voltage Range7-13 V
AccessoriesAnti-vibration screws and metal screws
Warranty60 months
EAN barcode4716123313328

Customer Reviews

Coolink SWiF2-800 80mm 1100 RPM 3-pin Quiet Cooling Fan

,

very quiet. just what i needed. i put 4 of these fans in a radiator heat deflector cowling and they are not audible at all from 400mm away.

Garishly designed but almost silent

,

I recently bought 4 of these to replace the standard fans in a 12 year old Lian-Li case. The ageing (cheap) fans were starting to make my computer sound like a Harrier Jump Jet. By comparison, these fans are nearly silent. Even with 4 of them running (1 at the rear of the case, 1 at the top and 2 at the frond to cool air flow over hard drives) there’s very little noise (other than the PSU and CPU fans). For such a low price I’m amazed! The bright colour of the rotating section did raise my eyebrows but this isn’t a problem with they’re mounted out of sight.

In summary, they’re cheap and quiet. Hard to not recommend them.

VERY QUIET Fan

,

Bought these Fans to fit into my new Silver stone Case (ML03), these fans helped to bring the Temp down by 5-8 Degrees.

They are so quiet that I can only hear them when I have my ear about an inch away from then, and this is just the air flow.

Also I love the green colour my HTPC looks cool with 4 of these fan all in a row up the side

Truly Quite

,

I have just received and fitted two Swif2 800 for an audio amplifier cooling application and they are incredibly silent, what a great product also fast and helpful advice from Andy at Quiet PC.

Actually completely silent!

,

I bought x2 Noctua NF-R8 80mm fans (because I had used them before and knew they were quiet) but I also bought one of these for my HTPC case as it claimed to produce only 9dB. I was extremely surprised at this product, and actually prefer it to my other Noctua fans, even at full throttle you can’t hear anything! not even the air! OK so it doesn’t spin as fast as the Noctua so it won’t move as much air, but it does shift plenty for something that makes no noise at all!

FAQ

  • How do I measure fan size?

    The size of fan you need will generally be determined by the size of the fan fitting position in your PC case. The sizes of all the fans on our website are shown as measured along any one of the fan’s four sides, NOT the distance between the fan’s screw holes! Our most popular fan size is 120mm, followed by 80mm. This isn’t really dictated by customer preference, but more by recent designs of PC cases.

    As for the thickness (depth) of the fan, generally 25mm (1 inch) is by far the most common depth, although smaller fans can have shallower depths such as 15mm or even 10mm. All our fans are 25mm thick unless otherwise stated. If you have any questions about which fan you should order, please don’t hesitate to get in touch.

    If you know the distance between the fan mounting screw holes but don’t know what fan size to order, please see the following table. Note that the mounting hole measurements shown below are taken horizontally or vertically between the holes and not diagonally.

    Screw hole spacings and fan sizes

    Space Between Screw Holes Fan Size
    32mm 40mm
    40mm 50mm
    50mm 60mm
    60mm 70mm
    72mm 80mm
    83mm 92mm
    105mm 120mm
  • I received a small cable (resistor) with my fan; what is it for?

    The resistor cable (also called Ultra Low Noise or ULN cable) is designed to allow the fan to run slightly slower for even quieter operation. The benefit in lower running noise is significant. Although the airflow will be reduced slightly, this usually has minimal effect on PC temperature. We would generally recommend using the ULN resistor cable for best results in almost all circumstances.

  • How can I tell which way the air blows through the fan?

    Hold the fan so that the round fan sticker is facing you. You are looking at the rear of the fan. When you plug the fan in, the air will be blowing towards you. If you want a fan to act as an air intake, then the fan sticker will be facing the inside of the case. Some fans also have two small arrows moulded into their plastic housing - one arrow shows the direction of airflow, and the other (at 90°) shows the direction of blade rotation.

  • Is it possible to use a 4-pin PWM fan or CPU cooler with a motherboard which has only 3-pin fan headers on it?

    Electrically, there is no problem doing this - the fourth pin on the fan cable is used purely for PWM control and is not needed in order for the fan to run. So you can plug the 4-pin fan connector onto the 3-pin motherboard fan header, leaving the fourth pin not connected to anything. The fan will potentially run at full speed, so if you would like to reduce the speed of the fan you will need to adjust the fan speed setting in your BIOS or use fan control software such as SpeedFan in Windows.

    The only other problem to consider is that occasionally, components immediately adjacent to the motherboard fan header can get in the way of the larger 4-pin fan connector, physically preventing connection. This problem also occurs if you try to use an in-line fan speed controller such as the one made by Gelid.

    Another avenue to explore is the possibility of using a bay-mounted fan controller. Several models are available now which provide 4-pin fan headers, so this is an easy way to use 4-pin PWM fans in a PC system which has only 3-pin fan headers on its motherboards. When using this method, you may find it necessary to disable any fan warning settings in your motherboard BIOS, since the motherboard may incorrectly believe that its CPU fan has failed when the fan is connected to a fan controller rather than directly to the motherboard itself.

Top Quiet Fans

Recently Viewed Products